MODIFICATION
20 -- Deckmounted Propulsion Units
- Notice Date
- 8/26/2004
- Notice Type
- Modification
- NAICS
- 335312
— Motor and Generator Manufacturing
- Contracting Office
- Department of the Air Force, Air Force Space Command, 45CONS (Bldg 423), 1201 Edward H White II St MS 7200, Patrick AFB, FL, 32925-3238
- ZIP Code
- 32925-3238
- Solicitation Number
- FA2521-04-R-0081
- Response Due
- 8/17/2004
- Archive Date
- 9/1/2004
- Point of Contact
- Christopher Slater, Contracting Specialist, Phone 321-494-9506, Fax 321-494-5136, - Linda Brantley, Contract Specialist, Phone 321-494-3668, Fax 321-494-2706,
- E-Mail Address
-
chris.slater@patrick.af.mil, linda.brantley@patrick.af.mil
- Small Business Set-Aside
- Total Small Business
- Description
- This modification is issued to chang the item description as follows: Item Description Transverse Mounted Propulsion Unit 1. SCOPE 1.1 Scope. This specification is for the procurement of transverse mounted propulsion units designed for and capable of propelling sectional cargo deck barges. The propulsion units shall be capable of being mounted transversely on the aft section of the cargo barge in order to reduce the overall space occupied and not degrade the barge?s cargo carrying capacity. 1.2 Quantity required. Two each 2. REQUIREMENTS 2.1 General 2.1.1 Pre-existing design. The propulsion unit(s) shall be of a pre-existing and proven design and manufacture, having demonstrated satisfactory performance, reliability, and durability. 2.1.2 General design and construction. The propulsion unit(s) shall be capable of installation without a need for separate supporting structures such as frames which project below main deck level. The unit(s) shall be secured to the deck by hold down bolts. An operators station or platform shall also be part of the design. The drive assembly shall be direct belt and gear driven and capable of withstanding all propeller generated thrust loads without the requirement for thrust bearing assemblies located below the deck level. The unit(s) shall be capable of being easily disconnected from the deck with the hold down bolts and be transportable without disassembly of propulsion unit components. 2.1.3 Size, weight, and configuration. Each propulsion base shall be five (5) feet wide (thwartships) X 3-4 feet length (longitudinal) excluding the stem and propeller overhang. The weight for the drive unit and stem should be 5.000 to 7,500 lbs. 2.1.4 Power requirements. The unit(s) shall be powered by commercially available diesel engines, four cycle, with a continuous duty rating of 125 HP to 150 HP. Engines shall have push-in type120V single phase, 1000 watt, heat shielded block heaters. The unit(s) shall have spark arrester exhaust systems with residential silencers. Lubrication and cooling requirements shall be provided for the units. Steering controls shall be hydraulically powered. Forward and reverse propeller thrust shall be capable of being attained fully. Propellers shall be heavy duty, commercially available type, sized with the proper diameter and pitch for the application involved; a spare propeller meeting the same specifications is required. Stem (or shaft) length required shall be 80 inches. The required fuel and hydraulic tanks shall be provided. An auxiliary 75 gal fuel tank is required in addition to the internal tank. 2.1.5 Finish and protective coatings. The unit(s) shall be coated and protected for use in a corrosive, marine environment, according to best commercial marine practices. 2.1.6 Performance. The unit(s) shall be suitable for installation on, and propulsion and maneuvering of 80 ft. long sectional cargo deck barges. 2.1.7 Maintainability. The unit(s) shall be capable of being maintained by Air Force personnel. 2.1.8 Commercial drawings and manuals and manufacturer?s recommended spare parts list. The unit(s) shall be provided with three (3) copies of a commercial owners/operators manual, service manual, and parts breakdown manual including recommended spare parts list. Three (3) copies of commercial installation drawings shall be provided. 3. QUALITY ASSURANCE PROVISIONS 3.1 Responsibility for inspection. The contractor is responsible for inspection and testing. Accompanying the unit(s), the contractor will provide the government documentation of testing in conformance with the contractor?s standard commercial practices for such testing. 4. PREPARATION FOR DELIVERY 4.1 Preservation and packaging shall be as specified in the contract. Proposals may be submitted via hard copy, fax (321-494-5136), or e-mail. NO HARD COPIES OF THE SOLICITATION WILL BE ISSUED FOR ANY REASON. Anticipated award date will be on or around 20 Sep 2004. Point of contact is Chuck Hobbs, 45 CONS/LGCBA, 1201 Edward H. White II, Street MS7200, Patrick AFB, FL 32925, (321) 494-6292, charles.hobbs@patrick.af.mil.
- Place of Performance
- Address: PATRICK AFB, FL
- Zip Code: 32925
- Country: USA
- Zip Code: 32925
- Record
- SN00655538-W 20040828/040827094356 (fbodaily.com)
- Source
-
FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |