MODIFICATION
J -- CGC BEAR EMERGENCY RUDDER REPAIR
- Notice Date
- 9/27/2004
- Notice Type
- Modification
- NAICS
- 336611
— Ship Building and Repairing
- Contracting Office
- DHS - Direct Reports, United States Coast Guard (USCG), Commanding Officer (vpl), USCG Maintenance and Logistics Command - Atlantic, 300 East Main Street Suite 600, Norfolk, VA, 23510-9102
- ZIP Code
- 23510-9102
- Solicitation Number
- HSCG80-04-Q-3FAW28
- Response Due
- 9/28/2004
- Archive Date
- 10/13/2004
- Point of Contact
- Mia Robinson, Contract Specialist, Phone 757-628-4654, Fax 757-628-4676, - Vanessa Nemara, Supervisory Contract Specialist, Phone 757-628-4634, Fax 757-628-4675,
- E-Mail Address
-
mrrobinson@mlca.uscg.mil, VNemara@MLCA.USCG.MIL
- Small Business Set-Aside
- Total Small Business
- Description
- The following changes have been made and are hereby incorporated into the combined synopsis/solicitation. The deadline of 28 September 2004 at 10:00 a.m. (Eastern Time) remains unchanged. The approximate Period of Performance is 29 September 2004 to 3 October 2004. 5 to 7 Days Calendar Days. The contractor must adhere to the quiet hours(0900–1200)being observed on the pier on 29 September 2004 for a Stand-up Ceremony. There will be no transportation of large machinery on/off the base or the running of cranes, compressors, or like equipment outside the skin of the ship. Work can; however, be accomplished within the skin of the ship during this time. Requirements 3.3 Carrier bearing clearance measurement. Before maintenance work is begun, the Contractor shall measure the rudder carrier bearing clearances of Port rudder. Submit CFR. 3.4 Rudder maintenance requirements. The Contractor shall perform the following for Port Rudder assembly: 3.4.2.3 Upper bearings. ·Clean and visually inspect the removed roller bearing. 3.4.2.4 Lower bearings. ·Visually inspect Port Thordon lower bearings for any abnormal or excessive wear. 3.4.4 Rudder reinstallation. Upon completion of all inspections and authorized repairs, if any, the Contractor shall reassemble and reinstall the Port rudder assembly, as shown on Coast Guard Drawings 901 WMEC 562-001 and 905 WMEC-004. Fill cavity below the new mechanical seal with grease, as shown on Coast Guard Drawing 905 WMEC-004. 3.8 Rudder air test. The Contractor shall air test the Port rudder in accordance with Std Spec 0740_STD, Appendix C. Submit CFR. Government Furnished Property: Rudder Assembly, NSN: 2040-01-486-0550, 1/ea is hereby removed from the list. Please submit acknowledgement of this amendment with your quotations. Lt Marino is the POC for technical questions. He can be reached at (787) 729-4387. ALL OTHER TERMS AND CONDITIONS OF THIS SOLICITATION REMAIN UNCHANGED. NOTE: THIS NOTICE WAS NOT POSTED TO WWW.FEDBIZOPPS.GOV ON THE DATE INDICATED IN THE NOTICE ITSELF (27-SEP-2004); HOWEVER, IT DID APPEAR IN THE FEDBIZOPPS FTP FEED ON THIS DATE. PLEASE CONTACT fbo.support@gsa.gov REGARDING THIS ISSUE.
- Web Link
-
Link to FedBizOpps document.
(http://www.eps.gov/spg/DHS-DR/USCG/COUSCGMLCA/HSCG80-04-Q-3FAW28/listing.html)
- Place of Performance
- Address: Coast Guard Base San Juan PR
- Record
- SN00683156-F 20040929/040927213133 (fbodaily.com)
- Source
-
FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |