SPECIAL NOTICE
51 -- 5180-01-395-2090
- Notice Date
- 3/31/2005
- Notice Type
- Special Notice
- NAICS
- 332212
— Hand and Edge Tool Manufacturing
- Contracting Office
- General Services Administration, Federal Supply Service (FSS), GSA Hardware SuperStore (6FE), 1500 East Bannister Road, Kansas City, MO, 64131
- ZIP Code
- 64131
- Solicitation Number
- 5180-01-395-2090
- Response Due
- 4/14/2005
- Archive Date
- 4/29/2005
- Description
- This is a notice of the governments intent to purchase NSN 5180 01 395 2090 quantity - 20. (Please note the quantity may increase slightly before the actual time of award). Aircraft Maintenance Tool Kit Enginetics Corp. p/n 140151. This purchase will be made using commercial acquisition procedures FAR part 12 and FAR part 13. For questions please contact Genia Watson @ 816 823-1296 or you may fax questions to 816-823-3109. Please fax any questions or concerns before noon on April 14, 2005. 5180-01-395-2090 UI: KT TOOL KIT, AIRCRAFT MAINTENANCE The following header paragraph(s) shall apply to the item purchase description(s) where applicable. If there is a conflict between the item purchase description and the header paragraph(s), the header paragraph(s) shall take precedence over the item purchase description. Notwithstanding the requirements specified herein, cadmium plating is not acceptable. In the event no alternative coating, finish, or plating is specified, a rust preventative finish as used in standard commercial practice shall apply. When chromium plating or finish is specified and the manufacturer has a commercial coating of the same color and texture of chromium that the manufacturer uses in lieu of chromium; then the alternative coating can be used, provided the coating meets Aerospace Standard SAE AS4984. Each set or kit shall contain a dated parts list or packing list citing the GSA contract number (if applicable), GSA purchase order number, date of purchase order, kit national stock number (NSN), each component NSN (if applicable), kit noun name, each component noun name, and quantity of each component. Unless otherwise specified in the item purchase description, each kit or set and each component of the kit or set shall have, in addition to any other required marking, identification marking indicating the manufacturer's name or identifying symbol, and the state or country of manufacture. The marking shall be engraved, etched, or stamped in such a manner that it will be permanent to the extent that it will remain clear and legible throughout the life of the item. Workmanship: Details of workmanship shall be in accordance with the best commercial standards and practices. Paints, coatings, platings, and finishes shall be smooth, adherent, continuous, and not stained or discolored. Fasteners shall be firmly secured and show no evidence of deformation, cross threading, or hazardous burrs. Adhesives and lubricants adequate for their intended purpose shall be properly and neatly applied. Adhesives shall be adequately cured. Wires and cables shall be neatly dressed and shall not be frayed or in contact with sharp edges. Wire and cable insulation shall show no evidence of burns, abrading, or pinch marks. There shall be no interference, binding, or galling of parts. External and bearing surfaces shall be free of tool and gouge marks, nicks, or other surface imperfections. The item shall be clean and free of corrosion and debris (e.g. chips shavings, slivers) or other foreign material. The item shall be free frommanufacturing workmanship defects (e.g., loose, missing, binding or misaligned parts, sharp or rough external edges, corners or surfaces) and material defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely impact the item's serviceability, durability, safety, or appearance. DESCRIPTION Tool Kit, Aircraft Maintenance with pin 140178-7 Stake, blank 140179-1 Stake 140179-3 Stake with pin 140179-7 Stake, blank 140180-1 Stake 140180-3 Stake with pin 140180-7 Stake, blank 140181-1 Stake 140181-3 Stake with pin 140181-7 Stake, blank 140185 Case 140186 Insert 070031 Label End of Components List. End Item Identification: Enginetics Corp. part number 140151. ITEM MARKING Mark each item in a permanent and legible manner with manufacturer's part number and name or identifying symbol. PACKAGING Packaging in accordance with standard commercial practice. PACKING The unit packages shall be packed in a close fitting fiberboard box in compliance with the Uniform Freight Classification and the National Motor Freight Classification requirements of Rules, Item 222, Sec. 3., Minimum 200, or ECT 32. MARKING All unit, intermediate, transport packages and unit loads shall be marked for delivery to civilian activities in accordance with the FED-STD-123G, dated June 6, 1997, or marked for delivery to military activities in accordance with MIL-STD-129P, change 2, dated 10 February, 2004, as applicable. PALLETIZATION Pallet Configuration: The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, double-face non-reversible pallets. Pallet lumber used shall be bark free. Pallet Load Size: The load plus the pallet shall have a maximum height of 53 inches and shall not exceed 2500 pounds in weight for shipments to Eastern Distribution Center (Burlington). The palletized load shall not exceed 2000 pounds in weightfor shipments to the Western Distribution Center (Sharpe). Pallet Load Configuration: The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Palletized loads shall be secured to the pallet to insure that theload arrives intact. Stacking Strength: The pallet plus the load shall be capable of supporting three additional like loads without any product damage and without the load or the pallet collapsing. Vertical, horizontal, or filler reinforcement may be added as necessary to provide strength. Partial Palletized Loads: Less than one-half pallet loads shall not be used for stacking, unless load is balanced on pallet. The partial palletized load shall be used for top loading only. NOTICE OF REQUIREMENTS FOR SHIPMENT TO EUROPEAN UNION COUNTRIES: Per Clause D-FSS-468, non-manufactured wood pallets and other non-manufactured wood package material used in shipments destined for ultimate delivery to or through a European Union (EU) country shall comply with the Emergency Measures (2001/219/EC) adopted by the Commission of the European Communities (CEC). Additionally, shipments delivered to DoD distribution facilities or freight consolidation points for eventual delivery to or through EU countries shall comply with DLA PROCLTR 01-15.
- Record
- SN00779751-W 20050402/050331212625 (fbodaily.com)
- Source
-
FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |