SOLICITATION NOTICE
42 -- SENTRY QUICKBERNS
- Notice Date
- 7/11/2007
- Notice Type
- Solicitation Notice
- NAICS
- 423840
— Industrial Supplies Merchant Wholesalers
- Contracting Office
- Department of the Air Force, Air Mobility Command, 60th CONS, 350 Hangar Ave. Bldg 549, Travis AFB, CA, 94535-2632, UNITED STATES
- ZIP Code
- 00000
- Solicitation Number
- Reference-Number-F3ZT937135A200
- Response Due
- 7/18/2007
- Archive Date
- 8/2/2007
- Description
- Travis AFB intends to award sole source contract to Basic Concepts, GS-07F-9543G, located at 1310 Harris Bridge Road, Anderson South Carolina 29621-3421 for the following item: CLIN 0001: Sentry Quickberns (this product is use for as fuel containment systems while deployed). This requirement is pursuant to Section 4202 of the Clinger-Cohen Act of 1996 as implemented by FAR 8.405-6(b). This is sole source due to standardization across AMC deployable Unit Type Codes and to comply with EPA regulations and standards. Basic Concepts is the manufacturer and sole distributor of their own products. All responsible sources may submit a bid, proposal, or quotation, which shall be considered by the agency. Contractor must be actively registered at CCR at http://www.ccr.gov and must complete FAR 52.212-3 (Representation and Certification) at http://www.orca.bpn.gov. All questions, comments, and response should be addressed to Nel Cadacio, Contract Specialist, 707-424-7729, E-mail at nel.cadacio@travis.af.mil or Josephine G. Cobb, 707 424-7720 NLT 17 Jul 2007. E-mail at josephine.cobb@travis.af.mil. Fax number is (707) 424-2712. Verbal requests will not be accepted. See below item and products specifications: 1. 4?x 6? x 1? Sentry quickberns XR-51.S ? 16 ea Capacity 179 gallons BCI-XR-002 2. 10? x 16? x 1? Sentry quickberns XR-5.1.S ? 5 ea Capacity 1198 gallons BCI-XR-019 3. 6? x 16? Ground mats ? 5 ea BCI GM-019 4. Deluxe repair kits XR-5 Material ? 5 ea BCI-DRP SENTRY QuickBerm Spill and Secondary Containment Product Specification Berm Design Specifications: 1. Patented inside support strap design to eliminate a tripping hazard. 2. All vertical walls with 1?? hem along the top edge and corner supports are to be extruded aluminum sealed in 4? wide pocketed berm material. 3. Wrap around corners with diagonal weld to prevent leakage. 4. Berms are one-piece heat welded design. Both ends of the support legs must be permanently attached to the berm. No assembly, no removable pieces. 5. In-house repair service using heat seal technology. Field repair kits are available. 6. All materials used in the manufacturing of the berm are 100% made in the USA, as well as the manufacturing itself. 7. Berm shall retain its form in termperatures up to 160 degrees F. 8. The berm shall be formed using RF welding with additional side hinging support members RF welded to the inside of the berm. 9. The walls of the berm shall be self-supporting. Berm Material: 1. Non-laminated berm material to be constructed of XR-5 or XR-3, 30oz., 30-mil material 100% American made Ethylene Interpolymer Alloy (EIA) Supported liner with these specifications: Base FabricType??..????????????????????????..?..Polyester Fabric Weight??????????????...?????????..???. 6.5 oz./sq. yd. Finished Coated Weight (ASTM-D751)???...????????????. 30 +/-2oz./sq.yd. Trapezoid Tear (ASTM D-4533) ??????????????????? 35/35 lbs. min. Grab Yield Tensile (ASTM D-751, Grab Method)?..??????????. 550/550 lbs. min. Elongation @Yield (%)???..?????????????????????? 20% min. Adhesion- Heat Seam (ASTM D-751 -Dielectric Weld)????..??????. 35 lbs./2" min. Adhesion- Ply (ASTM D-751, 2" min).?????????????????. 15 lbs./in min. or Film Tearing Bond Hydrostatic Resistance (ASTM D-751, Method A Proc. 1)??????????. 800 psi. min. Puncture Resistance (ASTM D-4833)??????????????????.. 250 lbs. min. Bursting Strength (ASTM D-751 Ball Tip)?????????.. ?650 lbs. min, (800 lbs. typ.) Dead Load (Mil-T-52983E Modified) Room Temperature?????????? 210 lbs. min. 160? F??????????. 105 lbs. min. Bonded Seam Strength (ASTM D-751, Seam Strength as Modified by NSF 54)???? 550 lb. Cold Crack (ASTM D-2136, 4 hours-1/8" Mandrel)????????????... Pass @ -30?F Weathering Resistance (Carbon-Arc Atlas Weather-o-meter)? ??????.. 8,000 hours min. with no appreciable changes or stiffening or cracking of coating Dimensional Stability (ASTM D-1204, 212?F.1 hour, each direction)??????...? l% Max. Water Absorption (ASTM D-471, 7 days)?????????????????????. 5% max. @ 70?F 12% max. @ 212?F Abrasion Resistance (Taber Method, Method 5306, ??????????????.. 2000 cycles before Fed, Std. 191a, H-18 Wheel, 100g load) fabric exposure 5Omg/100 cycles max. wt. loss Coefficient of Thermal Expansion/Contraction (ASTM E-228)????????...8x10 -6 in./in./ ?F. max. Permeability (ASTM D814-55, Kerosene ?????..???????? 0.02 oz/SF/Day max. And Transformer Oil with PCB Contamination Hydrocarbon Resistance -Kerosene, JP, Naptha, Diesel ?..??????.>95% Tensile strength (75 Months constant immersion with exposed base fabric) retention with no stiffening Transformer Oil Resistance -Univolt 60 (30 days immersion)...????.. >95% Tensile strength Shell Dialax (1 year immersion), exposed base fabric ... retention with no stiffening 2. Coating compound must contain DuPont Elvaloy that is essentially non-crystalline and therefore not susceptible to environmental stress cracking. 3. Key manufacturing step involves exclusive molecular primers being applied to saturate the woven fibers to make possible the binding of substrate and coating compound into as single system no delamination possible, no edge coating required. Laminates and layered products are not acceptable. 4. This material is warranted on a pro-rated basis for one year against both weathering and chemical compatibility. User is responsible for a sample test- immersion that will be evaluated by the manufacturer.
- Place of Performance
- Address: 573GSS, TRAVIS AFB, CA
- Zip Code: 94535
- Country: UNITED STATES
- Zip Code: 94535
- Record
- SN01339416-W 20070713/070711224104 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |