Loren Data's SAM Daily™

fbodaily.com
Home Today's SAM Search Archives Numbered Notes CBD Archives Subscribe
FBO DAILY ISSUE OF JULY 17, 2008 FBO #2425
SOLICITATION NOTICE

95 -- (4) Trunnion Pins, SEE DRAWING: MK 25/3-5; Expect Solicitation approx 17-Jul-2008

Notice Date
7/15/2008
 
Notice Type
Presolicitation
 
NAICS
332722 — Bolt, Nut, Screw, Rivet, and Washer Manufacturing
 
Contracting Office
Department of the Army, U.S. Army Corps of Engineers, US Army Corps of Engineers, Pittsburgh District, US Army Corps of Engineers, Pittsburgh District, 1000 Liberty Avenue, W.S. Moorhead Federal Building, 21st Floor, Pittsburgh, PA 15222-4186
 
ZIP Code
15222-4186
 
Solicitation Number
W911WN08T0017
 
Response Due
7/25/2008
 
Archive Date
9/23/2008
 
Point of Contact
Sue A. Gitto, 412-395-7114
 
Small Business Set-Aside
Total Small Business
 
Description
DESCRIPTION/SPECIFICATION FOR TRUNNION PIN, MK 25/3-5 1. SCOPE. This specification is for the manufacture and supply of a Trunnion Pin, Mark Number 25/3-5. The Trunnion Pin shall be supplied in accordance with the following specifications and details supplied on drawing number MK 25/3-5. 2. MATERIALS. The materials should conform to the following requirements. Forged Steel, ASTM A668, Class K 3. MACHINE WORK REQUIREMENTS. All workmanship shall be of the highest grade in accordance with the best modern practices to conform to the specifications for the item to be furnished. All sharp edges and corners shall be broken. All holes shall be normal to the surfaces of penetration and shall be sized as indicated on the reference drawing. 3.1. Dimensions and Tolerances. Tolerances for machine-finished surfaces designated by non-decimal dimensions shall be within +/- 0.010-inch unless otherwise noted on drawing MK 25/3-5. 3.2. Finished Surfaces. Surface finishes indicated on drawing number MK 25/3-5 or specified herein shall be in accordance with ANSI B46.1, Surface Texture (Surface Roughness, Waviness and Lay). Values of required roughness heights are arithmetical average deviation expressed in micro inches. These values are maximums. Lesser degrees will be satisfactory unless otherwise indicated on the drawings. Compliance with surface requirements shall be determined by sense of feel and visual inspection of the work compared to Roughness Comparison Specimens in accordance with the provisions of ANSI B46.1. Values of roughness width and waviness height shall be consistent with the general type of finish specified by roughness height. Where the finish is not indicated or specified, it shall be that which is most suitable for the particular surface, provide the class of fit required, and be indicated on the shop drawing by a symbol which conforms to ANSI B46.1 when machined finishing is provided. Flaws such as scratches, ridges, holes, peaks, cracks or checks which will make the part unsuitable for the intended purpose will be cause for rejection. 3.3. THREADS. Threads shall comply with ANSI B1.1, American National Standard for Unified Internal and External Screw Threads or ANSI B1.20.1 American National Standard Pipe Threads, General Purpose as designated on drawing MK 25/3-5. 3.4. Protection of Finished Work. Machined surfaces shall be thoroughly cleaned of foreign matter. All finished surfaces shall be protected by suitable means. 4. MARKINGS. Each part shall be legibly stamped on the top 11 inch diameter surface with HA - MK 25/3-5. The lettering shall be a minimum of 1/4 high. 5. CERTIFICATION OF MATERIAL COMPLIANCE. Certificates of compliance shall be submitted for all items demonstrating compliance of materials with the specification requirements. The certificate(s) shall verify that the supplied material complies with the established standards for physical and chemical properties for the material specified. Each certification shall be signed by an official authorized to certify on behalf of the manufacturing company and shall contain the name and address of the contractor, the contract number and the quantity and date(s) of shipment or delivery to which the certifications apply. 6. MATERIAL TEST REPORTS. Material Certification testing shall be performed and reports shall be submitted for all items supplied under the contract. The reports shall include a description of material, specifications, chemical properties and mechanical properties of the material used to manufacture the contract parts. Information shall be included which renders the reports identifiable and traceable with the specific parts manufactured for the contract. 7. PACKAGING. The Trunnion Pin shall be protected to the extent necessary to prevent damage during shipment. The contractor shall repair all damage incurred due to inadequate protection. The contractor shall provide all materials required for the protection of the Trunnion Pin during shipment. 8. SHIPPING. The contractor shall deliver the Trunnion Pin to the Pittsburgh Engineering Warehouse and Repair Shops (PEWARS) located at 3500 Grand Avenue, Neville Island, Pittsburgh, PA 15225-1584. Delivery of the Trunnion Pin shall be between 0800 and 1530 hours Monday through Friday.
 
Web Link
FedBizOpps Complete View
(https://www.fbo.gov/?s=opportunity&mode=form&id=89cfe93d5771f606578c585f1cce2f88&tab=core&_cview=1)
 
Place of Performance
Address: US Army Corps of Engineers, PREARS 3500 Grand Avenue Pittsburgh PA
Zip Code: 15225-1584
 
Record
SN01614152-W 20080717/080715222642-89cfe93d5771f606578c585f1cce2f88 (fbodaily.com)
 
Source
FedBizOpps Link to This Notice
(may not be valid after Archive Date)

FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |
ECGrid: EDI VAN Interconnect ECGridOS: EDI Web Services Interconnect API Government Data Publications CBDDisk Subscribers
 Privacy Policy  Jenny in Wanderland!  © 1994-2024, Loren Data Corp.