PRESOL | 58 | EVERTZ Analog Video Router P/N QT-3232N+2PS & Intelligent Control Panel P/N CP-1000E

FBO DAILY ISSUE OF AUGUST 25, 2011 FBO #3561
SOLICITATION NOTICE

58 -- EVERTZ Analog Video Router P/N QT-3232N+2PS & Intelligent Control Panel P/N CP-1000E

Notice Date: 8/23/2011
Notice Type: Combined Synopsis/Solicitation
NAICS: 334220 — Radio and Television Broadcasting and Wireless Communications Equipment Manufacturing
Contracting Office: Department of the Air Force, Air Force Materiel Command, AFFTC - AF Flight Test Center, 5 S WOLFE AVE, Edwards AFB, California, 93524-1185, United States
ZIP Code: 93524-1185
Solicitation Number: F1S0AE1214B001
Archive Date: 9/30/2011
Point of Contact: Steven A. Winner, Phone: 6612775686, MIKE KEELING, Phone: 6612772704
E-Mail Address: steven.winner@edwards.af.mil, mike.keeling@edwards.af.mil
(steven.winner@edwards.af.mil, mike.keeling@edwards.af.mil)
Small Business Set-Aside: Total Small Business
Description: Combined Synopsis/Solicitation - F1S0AE1214B001 This is a combined synopsis/solicitation for commercial items prepared IAW the format in FAR Subpart 12.6 as supplemented with additional information included in this notice. This announcement constitutes the only solicitation. Quotes are being requested and an additional written solicitation will not be issued. This is a Request For Quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Regulation (FAR) and Supplements, Federal Acquisition Circular (FAC) 2005-53 and DFARs Change Notice (DPN) 20110725. NAICS is 334220 with a small business size standard of 750 employees. This acquisition is a 100% small business set-aside. The Air Force Flight Test Center (AFFTC), at Edwards AFB, CA is seeking potential sources capable of providing an Evertz Analog Video Router W2 Redundant Power Supply P/N QT-3232+2PS and Evertz Intelligent Control Panel P/N CP-1000E which includes the following Specifications: BRAND NAME OR EQUAL TO: 1. PART NUBER QT-3232N+2PS EVERTZ ANALOG VIDEO ROUTER W2 REDUNDANT POWER SUPPLY 2. PART NUMBER CP-1000E EVERTZ INTELLIGENT CONTROL PANEL REQUIREMENTS: 1. QUANTITY ONE (1) EACH, PART NUBER QT-3232N+2PS EVERTZ ANALOG VIDEO ROUTER W2 REDUNDANT POWER SUPPLY 2. QUANTITY ONE (1) EACH, PART NUMBER CP-1000E EVERTZ INTELLIGENT CONTROL PANEL MINIMUM SALIENT CHARACTERISTICS/SPECIFICATIONS FOR EVERTZ ANALOG VIDEO ROUTER W2 REDUNDANT POWER SUPPLY P/N QT-3232+2PS AND EVERTZ INTELLIGENT CONTROL PANEL P/N CP-1000E: Following are the specific technical requirements for these items, all of which the Evertz Analog Video Router W2 Redundant Power Supply P/N QT-3232+2PS and the Evertz Intelligent Control Panel P/N CP-1000E units meet: a. The switch shall have at least 32 inputs and outputs. These inputs and outputs must be BNC coaxial type connections. This switch is intended to switch NTSC video. NTSC video is a single-cable analog signal as used by standard Television (pre-Feb 2009). The switch should be non-blocking, meaning that any combination of inputs and outputs may be cross connected without restrictions. The cross connect "points" in the switch should not be mechanical in nature (i.e. they should not be relays). b. The system shall include a control panel to allow the user to issue switch commands without the need of a separate full-sized computer. The switch must have an internal controller that will communicate with the control panel. The controller needs to be programmable to allow the input and output ports to be given user-friendly names and to allow the control panel to use those names. c. The system shall provide the necessary setup software (if special software is needed). The software, if needed, shall be "user friendly" in that it does not require the user to have special knowledge to accomplish the setup of the switch and control panel. Any special setup programming cables needed shall be supplied with the system. d. The switch shall not be larger than two rack units in height. The control panel shall be a separate item that can be mounted at a different location from the switch proper, and one rack unit in height. An internal control panel would be placed in an awkward position, i.e., floor-level, with the current mounting position of the switch in our rooms. The switch and control panel power supplies may be internal or external to the device. e. Following are additional technical specifications that would have to be matched, in general, for a different unit to be compatible with the requirements: For the Switch: EVERTZ ANALOG VIDEO ROUTER W2 REDUNDANT POWER SUPPLY P/N: QT-3232N+2PS Configuration The modular design of the Q-32N routers give them a high degree of flexibility, allowing them to be easily configured in square or non-square sizes. The Q32-N is housed in a 2RU frame. The Q32-N is available in three fixed sizes -16x16, 32x16 and 32x32. The Q32-N can be upgraded by returning the router to the local service center. Control The Q32-N router includes, as standard, an internal Frame Controller module which supports a single Q-Link and Serial port on the rear of the router. The optional internal CI module can be fitted to the Q32-N to increase the number of Q-Link and Serial ports. The Q32-N has a number of control options, they are: Passive Remote Control Panels: The CP-1601A-P and CP-1604-P passive remote control panels can be fitted to the Q32-N routers via a PI-1604 or PI-1608 parallel interface. Remote Control Panel: Any panel(s) from the entire range of Quartz remote control panels can be used with the Q32-N router connected via Q-Link. External Third Party Control: The Q32-N routers can be remotely controlled via an external third party control device such as an automation system, when connected to the router's serial port. Expansion The input or output stage of the Q32-N can be expanded from 16 to 32. Power Supply The power supply for the Q32-N is internal. The 2RU Q32-N frame can be fitted with an optional redundant power supply with separate AC power inlet and alarm output. Analog Video: Terminated inputs for best possible signal performance. DC restored inputs for composite signals ensures switching free from the picture disturbances often encountered in DC-coupled-only designs. Vertical interval switching for clean switching reverts to free running if no sync reference (video or pulse), with all levels of the same route switching in the same field. Frames can be stacked for parallel component analog video routers, or a single frame can be split to provide, for example, four separate 8x8 routers from a single 32x32 frame. Operational Features: Diagnostic monitoring of temperature and PSU status. All modules are installed from the front for easy access for upgrades and maintenance not possible with some alternative designs. Built-in control system. Electrical and Interface Specifications: Configuration: Inputs: Q32 Selectable, 16 or 32 Outputs: Q32 Selectable 4, 8, 16, or 32 Analog Video Inputs: Signal level: 1V p-p nominal, +3dB max Impedance: 75Ω terminating Return Loss to 5.5MHz: 40dB Connectors: BNC per IEC 61169-8 Annex A Analog Video Outputs Impedance: 75Ω Return Loss to 5.5MHz 40dB DC on output: ±50mV Connectors: BNC per IEC 61169-8 Annex A Signal Path: Insertion gain: ±0.ldB HF response: 15kHz to 5.5MHz ±0.ldB to 30MHz +0.2, -0.5dB to 100MHz -3dB LF response, tilt at 50Hz: 0.5% 2T pulse, pulse/bar, bar slope: 0.25%K Luma/Chroma inequalities: ±0.5% gain, ±5ns delay DiffGain and Phase: 0.1%, 0.1° (10-90% APL) Luminance non-linearity: 0.2% Path length, typical: 10ns Timing spread at 3.58/4.43MHz: ±l° at any output Crosstalk at 3.58/4.43MHz: -57dB Noise to 5.5MHz: -70dB rms Control: Q-link to remote panels: 1 as standard (additional 3 Q-links optional) 75Ω video cable 500m max. length Serial RS232/422: 1 as standard (additional serial port optional) D9 female Switching Reference: Signal level: 1V p-p ±3dB or 1-4V pulses 525 or 625 line Impedance: 75Ω (loop through) Switching Line: Lines 6/319 (675); Lines 10/273 (525) Power: Supply: Auto ranging 100 to 240VAC 50/60Hz Power Consumption: 12W Backup: Option with alarm output on 2U frame Physical: Height: 2RU, 88mm (3.5" nom.) Width: 19" (483mm) Depth: 19" nom (483mm) Weight: 6.6kg Operating Temp: 0-40°C Spec Maintained: lO-30°C Ventilation: Natural convection For the Control Panel Unit: EVERTZ INTELLIGENT CONTROL PANEL P/N CP-1000E Flexible feature or menu driven configurations providing quick and simple access. Easily reconfigured for regularly changing environments. Each LCD display features a 32x24 dot matrix capable of supporting three rows of five character text or a graphic. Each LCD illumination can be red, green or yellow with a two-level programmable intensity providing unprecedented visual indication of the button status. Fully programmable button operation -user-definable via WinSetup configuration software. Button-per-source selection with Page mode NEXT and LAST buttons to select more sources. LOCK or ENABLE button to protect against unauthorized or accidental selection. Buttons can be programmed for breakaways or to give a menu structure to the panel. Camera joystick override on any eight inputs, with momentary or latching action. Electrical and Interface Specifications: Control: Q-link to remote panels: 75Ω video cable 500m max. length Serial RS232/422 (Optional): D9 female Parallel (Joystick override): D9 male, TTL levels Ethernet: 10/100 Base T; RJ45 connector Power: Supply: 100-132V, l80-240VAC, 50/60Hz Consumption: 15W Physical: Height: 1RU, 44mm Width: 19" rack mount Depth: 130mm Weight: 1.85kg Operating Temp: D-40oe Delivery: 60 DARO or Less Place of delivery, performance, and acceptance is FOB Destination, Edwards AFB, CA 93524. Interested parties who believe they can meet all the requirements for the items described in this synopsis are invited to submit in writing a complete quote including delivery FOB destination Edwards AFB, CA 93524. Offerors are required to submit with their quote enough information for the Government to evaluate the minimum requirements detailed in this synopsis. CONTRACTORS MUST COMPLY WITH FAR 52.204-7 CENTRAL CONTRACTOR REGISTRATION AND DFARS 252.204-7004, ALTERNATE A. INTERESTED CONTRACTORS CAN ACCESS THE CLAUSES BY INTERNET URL: http://farsite.hill.af.mil. TO REGISTER WITH THE CCR, GO TO URL: http://www.ccr.gov/. ONLINE REPRESENTATIONS AND CERTIFICATIONS APPLICATION (ORCA) MUST BE COMPLETED. USE OF ONLINE REPRESENTATIONS AND CERTIFICATIONS APPLICATION (ORCA) BECAME MANDATORY 1 JANUARY 2005. CONTRACTORS CAN ACCESS ORCA THROUGH CCR BY INTERNET URL: http://www.ccr.gov/. The following provisions and clauses apply: Clause 52.211-6 Brand Name or Equal; Provision 52.212-1, Instructions to Offerors--Commercial; Clause 52.212-2 Evaluation-Commercial Items; the following factor shall be used to evaluate offers: Lowest price technically acceptable offer, Technically acceptable is meeting all minimum salient characteristics; clause 52.212-4, Contract Terms and Conditions--Commercial Items; clause 52.212-5, Contract Terms and Conditions Required to Implement Statutes Or Executive Orders--Commercial Items (to include: 52.222-26, Equal Opportunity; 52.222-35, Affirmative Action for Special Disabled and Vietnam Era Veterans; 52.222-36, Affirmative Action for Handicapped Workers; 52.222-37, Employment Reports on Special Disabled Veterans and Veterans of the Vietnam Era); Clause 52.232-33 Mandatory information for electronic funds transfer payment. The following DFARs clauses apply to this acquisition: Clause 252.212-7001, Contract Terms and Conditions Required to Implement Statutes or Executive Orders Applicable to Defense Acquisition of Commercial Items; 252.225-7001 Buy American Act and Balance of Payment Program: The following AFFARS clauses apply to this acquisition: Clause 5352.223-9000, Elimination of Use of Class I Ozone Depleting Materials, 252.211-7003, Item Identification and valuation; 252.232-7010. Levies on Contract Payments; 5352.201-910, Ombudsman; 5352.242-9000, Offers are due at the Air Force Flight Test Center, Directorate of Contracting, 5 South Wolfe Avenue, Building 2800, Edwards AFB, CA, 93524, not later than September 1, 2011 at 3:30 pm PST. E-mail address: steven.winner@edwards.af.mil. Phone: 661-277-5686 Fax: 661-277-0470
Web Link: FBO.gov Permalink
(https://www.fbo.gov/spg/USAF/AFMC/AFFTC/F1S0AE1214B001/listing.html)
Place of Performance: Address: AFFTC/PKEE, 5 South Wolfe Avenue, Bldg. 2800, Edwards Air Force Base, California, 93524, United States; Zip Code: 93524
Record: SN02546367-W 20110825/110824000546-2ea36b32f105ebcfd2c46e5cd92292f9 (fbodaily.com)
Source: FedBizOpps Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's FBO Daily Index Page |

Loren Data's SAM Daily™

58 -- EVERTZ Analog Video Router P/N QT-3232N+2PS & Intelligent Control Panel P/N CP-1000E