SOURCES SOUGHT
56 -- ESD Sheet Flooring of US Manufacture
- Notice Date
- 2/6/2012
- Notice Type
- Sources Sought
- NAICS
- 238330
— Flooring Contractors
- Contracting Office
- Department of Energy, Brookhaven National Laboratory (DOE Contractor), Brookhaven, PO Box 5000, Bldg. No. 355, Upton, New York, 11973
- ZIP Code
- 11973
- Solicitation Number
- ESDfloor
- Archive Date
- 2/14/2012
- Point of Contact
- David J. Paveglio, Phone: 631-344-8461
- E-Mail Address
-
dpavegli@bnl.gov
(dpavegli@bnl.gov)
- Small Business Set-Aside
- N/A
- Description
- BSA is interested in locating a source domestically manufactured ESD sheet flooring. Manufacuters/Dealers with an ESD Sheet flooring product of domestic manufacture and meeting the Secifications set forth below should contact D. Paveglio. STATIC DISSIPATIVE SHEET RUBBER FLOORING (SDSR) ) PART 1 - GENERAL 1.1 QUALITY ASSURANCE •A. Comply with International Institute of Synthetic Rubber Producers, standards. •B. Fire and smoke ratings: •1. Critical radiant flux: Class I, not less than 0.45 W/cm', in accordance with ASTM-E648 and NFPA 253. •2. Smoke developed: 450 or less, in accordance with ASTM-E662 and NFP A 258. •3. Flame spread: Maximum 75 in accordance with ASTM-E84. •4. Usage: •a. NFPA 101. •b. NFPA 99. •C. Static load limit: 75 psi in accordance with ASTM-F970. •D. Electrical resistance: 1,000,000 to 100,000,000 ohms in accordance with ESD-S.7 and ASTM­F150. •E. Static generation: Less than 100 volts at 12 percent relative humidity and less than 10 volts at 40 percent relative humidity, with ESD footwear, in accordance with ESD-STM 97.2. •F. Static decay: 5000 volts to zero in less than 0.5 seconds, with ESD footwear, in accordance with Federal Test 101C, Method 4046. •G. Static coefficient of friction: Minimum 0.6 in accordance with ASTM-D2047. •H. Installer qualifications: Installer shall be approved by product manufacturer to meet the requirements of this project. •I. Comply with Fed Spec SS-T-312B. •1. Provide static dissipative flooring, adhesive, copper grounding strips, and maintenance finish supplied by one manufacturer. •J. LEED Information: •1. LEED Credit EQ 4. I, Low-Emitting Materials, Adhesives: Product data indicating that volatile organic compound (VOC) levels of adhesives are in compliance with South Coast Air Quality Management District (SCAQMD) regulations. •2. LEED Credit MR 5.1, Local/Regional Materials: Manufacturer's certification indicating final point of assembly for products and materials located within 500 miles of Project site. Include manufacturer's name, address and phone number. 1.2 WARRANTY •A. Manufacturer: Warrant product against wear exceeding 10 percent for a period of 5 years. •B. Installer: Warrant installation against loss of bond to substrate and seam separation for a period of 5 years. PART 2 - PRODUCTS 2.1 MATERIALS •A. Acceptable manufacturers: •1. Static Dissipative Sheet Rubber (SDSR) flooring: •a. Base: I) Freudenberg Building Systems, Inc. •B. Static Dissipative Sheet Rubber Flooring: •1. Product: noraplan mega ed, Article 100, ESD control, static dissipative, oil and grease resistant. •2. Material: nora rubber Compound 948 with abundant natural fillers and environmentally compatible color pigments. •3. Roll Size: 0.08 IN thickness, 48.2 FT x 48 IN •4. Back of Tile: Smooth, sanded back. •5. Limited Wear/Conductivity Warranty: 5 year wear; 10 year conductivity. •6. Standard: ASTM F 1344, for solid color homogeneous tiles and through-mottled tiles as applicable. •7. Abrasion Resistance: Taber abrasion test, ASTM D 3389, H-18 wheel, 500 gram load, 1000 cycles, gram weight loss not greater than 0.70. •8. Hardness: ASTM D 2240, Shore A, not less than 85. •9. Slip Resistance: Static coefficient of friction (James Test): ASTM D 2047, equal to or greater than 0.5. •10. Asbestos-Free: Products shall contain no asbestos. 11. Flammability: ASTM E 648; NFPA 253; NBSIR 75 950 result to be not less than 0.45 watts per square centimeter, Class 1. •12. Smoke Density: ASTM E 662, NFPA 258, NBS smoke density, less than 450. •13. Bacteria Resistance: Products shall be resistant to bacteria, fungi, and micro-organism activity, according to ASTM E 2180 and ASTM G 21. •14. Bum Resistance: Cigarette and solder bum resistance. •15. Halogen-Free: Products shall contain no halogens. •16. PVC-Free: Products shall contain no poly-vinyl-chloride. •17. IAQ: Products shall meet GreenGaurd requirements. •18. Conductivity: 106 -less than or equal to 10 9 resistance to ground for when tested according to ASTM F 150 and ESD.S7.1 under> 30 percent relative humidity at room temperature. •19. Decay Time: < 0.25 seconds when tested according to FTM 4046.101. •20. Static Generation: < 20 volts when tested according to ESD STM 97.2. •21. ISO 14001 : Manufacturer shall be ISO 14001 Environmental Management System Certified. •22. LEED requirements: Maximum VOC content of 50 g/L. •23. Color: As selected. •24. Static Load: Per ASTM F-970 Standard Test Method for Static Load Limit, residual compression, when tested with 800 LBS results shall be ≤0.005".
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DOE/BHL/BNL/ESDfloor/listing.html)
- Place of Performance
- Address: Brookhaven National Laboratory, Upton,, New York, 11973, United States
- Zip Code: 11973
- Zip Code: 11973
- Record
- SN02668364-W 20120208/120206234423-068e34391f4439b30f54881e5e90840f (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |