SOURCES SOUGHT
34 -- Vertical Band Saw
- Notice Date
- 8/27/2015
- Notice Type
- Sources Sought
- Contracting Office
- ACC-RSA-CCAD - (SPS), ATTN: SIOCC-RS-AQ, 308 Crecy Street, Corpus Christi, TX 78419-6170
- ZIP Code
- 78419-6170
- Solicitation Number
- W912NW-BAND-SAW
- Response Due
- 9/14/2015
- Archive Date
- 10/26/2015
- Point of Contact
- George Kapusta, 361-961-2564
- E-Mail Address
-
ACC-RSA-CCAD - (SPS)
(george.a.kapusta.civ@mail.mil)
- Small Business Set-Aside
- Total Small Business
- Description
- Shop (End User) Requirements & Technical Specifications for Vertical Band Saw Must have a minimum cutting capacity of 23 quote mark Vertical x 18 quote mark Horizontal, 18 quote mark Round when cutting at 90 Degrees. Must have a minimum cutting capacity of 15.75 quote mark Vertical x 18 quote mark Horizontal, 15.75 quote mark Round when cutting at 45 Degrees. Must have a minimum cutting capacity of 10.75 quote mark Vertical x 18 quote mark Horizontal, 10.75 quote mark Round when cutting at 60 Degrees. The saw bow must be able to automatically return to the zero degrees position after the cuts are completed. Must have an upper guide arm (acts as a linear guide for positive smoother positioning). Must have hydraulically actuated positioning. Must have at a minimum a 5hp motor for the blade drive Must have at a minimum a 1/8hp motor for the cutting fluid pump. Must have a 230Volt, 3-Phase Electrical hook up for the entire system. Must have an automatic hydraulically applied blade tension maintained at 30,000 PSI. The machine must be able to automatically notice when a blade breaks or stalls and must automatically turn off when this occurs. Must have a blade speed range of 0 to 450 Surface Feet per Minute (SFPM) infinitely variable. This must be able to be controlled at the front panel along with a digital display of the blade speed. At a minimum, must have a 12 gallon cutting fluid capacity. At a minimum, must have a 20 gallon hydraulic oil capacity. Must have roller bearing pre and post blade guides. The blade must be fluid driven (hydraulic). Must have an independently controlled feed rate and feed pressure functions whose valves are infinitely variable with pressures ranging from 0 to 425lbs. Must come with a mounted blade cleaning brush that has the capability of adjusting with the speed of the blade. Must have a hydraulic column tilt (minimum 60degrees left or right of center). Degree of tilt must be plainly visible from the operator's station. Must be able to cant the blade anywhere from upright to 6degrees forward cant. Must have at least 2 quote mark T-Slots quote mark to be used for fixtures. Must have, at a minimum, a 7 quote mark high, full stroke hydraulic, left hand side vise. The operators control panel must be located at the front of the machine in a fixed position and not interfere with the view of the cutting area. Must have at least one high intensity LED work lamp on or near the saw blade/ wheel cover assemblies. Must come with a total of 15feet of dead roller tables with 2-1/2 quote mark rollers. Must have a digital readout of tilt angle located on the front control panel. Must come equipped with a variable vise pressure to allow for cutting of thin wall materials.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/notices/57e68010011a1155d54fdda31733d100)
- Place of Performance
- Address: ACC-RSA-CCAD - (SPS) ATTN: SIOCC-RS-AQ, 308 Crecy Street Corpus Christi TX
- Zip Code: 78419-6170
- Zip Code: 78419-6170
- Record
- SN03859384-W 20150829/150827235951-57e68010011a1155d54fdda31733d100 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |