SOURCES SOUGHT
10 -- Manufacturing Capabilities 105mm Thermal Shrouds
- Notice Date
- 11/3/2018
- Notice Type
- Sources Sought
- NAICS
- 332710
— Machine Shops
- Contracting Office
- Department of the Army, Army Contracting Command, ACC - WRN (W911PT)(WVA), 1 BUFFINGTON ST BLDG 10, Watervliet, New York, 12189-4000, United States
- ZIP Code
- 12189-4000
- Solicitation Number
- W911PT19SSThermShrouds
- Archive Date
- 1/30/2019
- Point of Contact
- Gerard S Mangione, Phone: 5182665439, Jaclyn Beadnell, Phone: 5182665757
- E-Mail Address
-
gerard.s.mangione.civ@mail.mil, jaclyn.r.beadnell.civ@mail.mil
(gerard.s.mangione.civ@mail.mil, jaclyn.r.beadnell.civ@mail.mil)
- Small Business Set-Aside
- N/A
- Description
- Sources Sought Notice for: Capabilities to Manufacture Front and Rear XM-35 105mm Thermal Shrouds The U.S. Army Contracting Command - Warren (ACC-WRN) WVA Contracting Office located at Watervliet Arsenal is conducting a market survey to identify potential capable sources for the manufacture of Front and Rear XM-35 105mm Thermal Shrouds. THERE IS NO SOLICITATION AT THIS TIME AND NO CONTRACT WILL BE AWARDED FROM THIS NOTICE. This is a request for information on capabilities and interest and does not constitute a Request for Proposal (RFP); submission of any information in response to this market survey is purely voluntary and the U.S. Government (USG) assumes no financial responsibility for any costs incurred. No funds have been authorized, appropriated, or received for this effort. Data submitted in response to this market survey will not be returned. ITEM DESCRIPTION AND CAPABILITIES: 1. Material Spec. - T6060-T6 per ASTM B221 or B241( Extruded Aluminum Alloy heavy wall tubing, bar stock or Seamless tubing) 2. REAR SHOURDS: Raw Materials sizes required, 9.250" OD X 1.625 wall thickness tubing X 75" long & 54" long, or 9.250" x 75" long & 54" long bar stock: depending on shroud configuration. 3. FRONT SHROUDS: Raw Materials required, 7.750" OD X 1.00 wall thickness tubing X 75" long & or 7.750" x 75" bar stock: depending on shroud configuration. 4. If bar stock is to be used, manufacturer should have the machining capabilities to drill/bore deep hole to near size for finish contour of internal dimensions. WVA may be able help in pre-boring solid bar stock if required. 5. Manufacturer must have machine tool capabilities to turn / thread required outside dimensions and details. Hold positional, length and diametrical tolerances of.001" where applicable. This may include making of shop floor made fixtures, e.g. - turning plugs, cat head rings & supports. 6. Manufacturer must have machine tool capabilities to bore / thread required inside dimensions and details, e.g. Long enough boring bars, suitable tooling holders, etc. Hold positional tolerances, length and diametrical tolerances of.001" where applicable. Again, shop floor made fixtures may be needed. 7. Manufacturer must have machine tool capabilities to mill / drill / ream / tap required features and details. Hold positional, length and diametrical tolerances of.0002" where applicable. 8. Manufacturer must be able to achieve surface finishes of 63 RMS or better on required surfaces. 9. Manufacturer must be able to inspect finish components to drawing requirements. Produce an inspection report with all variable data recorded. 10. Component protective finish requirements to be completed by manufacturer. 11. Drawings of components will be supplied for process development and machine tool selection. 12. This is a rough outline of required capabilities to be able to manufacture components listed above. INTERESTED PARTIES. The Government requests interested parties to submit a company brochure (if available) and a tailored capability statement for these requirements that clearly details the ability to perform the aspects of the notice described above. All proprietary information should be marked as such. The description should also include any anticipated needs for sub-tier Responses will be reviewed by U.S. Army Contracting Command - Warren (ACC-WRN) (WVA), Watervliet Arsenal and the US Army personnel only and will be held in a confidential manner. Any and all information provided shall include a description of the proposed manufacturing capabilities. Submitted documentation will not be returned. Submission Information: Responses to this sources sought synopsis should be submitted within 15 days from the date of this publication via email. Interested firms should provide their address, point of contact information with telephone number and e-mail address. The Point of Contact for this action is: Mr. Gerard S. Mangione Army Contracting Command - Warren (ACC-WRN) (WVA) Building 10 1 Buffington Street Watervliet NY, 12189-4000 Email: gerard.s.mangione.civ@mail.mil
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/notices/eb0fe986fa725576008838e6c24941ce)
- Place of Performance
- Address: Army Contracting Command - Warren (WVA), (ACC-WRN)(WVA) Attn:, Building 10, Watervliet, New York 12189, United States, Watervliet, New York, 12189, United States
- Zip Code: 12189
- Zip Code: 12189
- Record
- SN05142684-W 20181105/181103230032-eb0fe986fa725576008838e6c24941ce (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |