SOLICITATION NOTICE
48 -- SERVOVALVE, HYDRAULIC
- Notice Date
- 7/1/2020 3:22:29 PM
- Notice Type
- Presolicitation
- NAICS
- 336992
— Military Armored Vehicle, Tank, and Tank Component Manufacturing
- Contracting Office
- DLA LAND AND MARITIME COLUMBUS OH 43218-3990 USA
- ZIP Code
- 43218-3990
- Solicitation Number
- SPE7MC20R0018
- Response Due
- 8/14/2020 8:59:00 PM
- Archive Date
- 08/29/2020
- Point of Contact
- Teresa Kershaw, Phone: 6146923029
- E-Mail Address
-
teresa.kershaw@dla.mil
(teresa.kershaw@dla.mil)
- Description
- RESPONSE DATE:� Offers/Responses are due prior to the Closing Date and Time specified in BLOCK 9 on Page 1 of the Solicitation/Request for Proposal (RFP). The solicitation will be available in DIBBS on or about its estimated issue date of July 15, 2020.� DESCRIPTION: NSN(s): 4810-013676181 Item Description: SERVOVALVE, HYDRAULIC RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RD002, COVERED DEFENSE INFORMATION APPLIES Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS.� FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES THE TECHNICAL/QUALITY/TEST REQUIREMENTS FOR CITED P/N WILL BE IN CONFORMANCE WITH THE LISTED DRAWING. MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 19200 12561758 REVISION NR K�� DTD 09/29/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 11654514 REVISION NR R�� DTD 11/02/1984 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553887 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553888 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553890 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553891 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553892 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553893 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553894 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553895 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553896 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12553897 REVISION NR B�� DTD 06/13/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12561783 REVISION NR C�� DTD 08/06/1993 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12561786 REVISION NR D�� DTD 05/15/1995 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12561788 REVISION NR B�� DTD 05/15/1995 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12562010 REVISION NR B�� DTD 05/15/1995 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12561777 REVISION NR A�� DTD 05/21/1991 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12940848 REVISION NR B�� DTD 06/05/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 G5P2012 REVISION NR���� DTD PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81349 MIL-S-71076 REVISION NR���� DTD PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81349 MIL-S-71076-001 REVISION NR���� DTD PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12979819 REVISION NR���� DTD 03/12/1996 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12553888 REVISION NR C�� DTD 12/02/1997 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12553890 REVISION NR C�� DTD 12/02/1997 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12553891 REVISION NR C�� DTD 12/02/1997 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12553894 REVISION NR C�� DTD 12/02/1997 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12561777 REVISION NR D�� DTD 03/11/1997 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12561783 REVISION NR D�� DTD 12/02/1997 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12579607 REVISION NR C�� DTD 08/04/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12561786 REVISION NR G�� DTD 08/28/2000 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12369002 REVISION NR H�� DTD 12/15/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12561787 REVISION NR C�� DTD PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12496537 REVISION NR D�� DTD 03/25/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12561758 REVISION NR���� DTD 07/11/2019 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13013641 REVISION NR A�� DTD 12/17/2018 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12561758 REVISION NR���� DTD 02/18/2014 PART PIECE NUMBER: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001� PRES MTHD:ZZ� CLNG/DRY:Z� PRESV MAT:ZZ WRAP MAT:ZZ� CUSH/DUNN MAT:ZZ� CUSH/DUNN THKNESS:Z UNIT CONT:ZZ� OPI:A INTRMDTE CONT:ZZ� INTRMDTE CONT QTY:ZZZ PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008 14DLA0462R�� DATE: - 27 FEBRUARY 2014 NSN:-4810-01-367-6181 PRESERVATION: MILITARY LEVEL OF PACKING: -B-- QUANTITY PER UNIT PACKAGE: -001- SPI NUMBER 12561758�� DATED 18 FEB 14, REV - ZZ - SPECIAL MARKING REQUIREMENTS: REQUIRED: PER MIL-STD-129, SERIAL NUMBER SHALL BE MARKED ON THE UNIT, INTERMEDIATE, AND SHIPPING CONTAINERS. ZZ -ADDITIONAL SPECIAL MARKING: Protected Cargo (Controlled, Sensitive, Classified, Pilferable items). Special Marking Code 40 applies -- ""Markings shall be omitted for sensitive, controlled or pilferable items per MIL-STD-129."" The item description (nomenclature) shall be omitted from all shipping containers of protected cargo. See MIL-STD-129, paragraph 5.4.1.6 (Protected Cargo) for more information. A prototype package is required to validate the sizes and fit requirements of the SPI SEE SECTION C FOR CHANGES/UPDATES TO SPI If Product First Article Testing (FAT) is required and a Packaging FAT is included in the Special Packaging Instruction or Drawing, the Packaging FAT requirement is invoked. If there is no Product FAT, no Packaging FAT is required. Quantity (including option quantity):� ESTIMATED ANNUAL DEMAND = 5 Unit of Issue:� EACH Destination Information:� Various DLA stocking locations Delivery Schedule:� 466 Days All responsible sources may submit an offer/quote which shall be considered.� (X) The proposed contract Unrestricted. (X)� The Small Business size standard is 1500 employees. (X)� While price may be a significant factor in the evaluation of offers, the final award decision will be based upon a combination of price, delivery, past performance and other evaluation factors as described in the solicitation. (X)� Various Increments Solicited: (X)� Quantity ranges will be solicited. (X)� Drawings/specifications will be available through the DIBBS solicitation link in the synopsis on the solicitation issue date. (X) One or more of the items under this acquisition may be subject to an Agreement on Government Procurement approved and implemented in the United States by the Trade Agreements Act of 1979. All offers shall be in the English language and in U.S. dollars. All interested suppliers may submit an offer. (X) Based upon market research, the Government is not using the policies contained in Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice.
- Web Link
-
SAM.gov Permalink
(https://beta.sam.gov/opp/f1c9cfdbf243426c984052537093890c/view)
- Record
- SN05710002-F 20200703/200701230146 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |