SOLICITATION NOTICE
17 -- Arresting Engine Cylinders and Filler Bar Mandrel
- Notice Date
- 12/23/2020 7:27:15 AM
- Notice Type
- Presolicitation
- NAICS
- 332710
— Machine Shops
- Contracting Office
- USA WATERVLIET ARSENAL WATERVLIET NY 12189-4000 USA
- ZIP Code
- 12189-4000
- Solicitation Number
- W911PT21R0006
- Response Due
- 1/7/2021 1:00:00 PM
- Archive Date
- 03/15/2021
- Point of Contact
- Peter J. Haschytz II, Phone: 5182663933
- E-Mail Address
-
peter.j.haschytz.civ@mail.mil
(peter.j.haschytz.civ@mail.mil)
- Description
- Two (2) each Arresting Engine Cylinders per drawing�P629297 Rev B; Five (5) each Arresting Engine Cylinders, test section, per drawing MISC-OA474; One each 20"" filler bar mandrel per drawing BL-55662 Rev New with additional information as follows: ITEM DESCRIPTION AND CAPABILITIES: Arresting Engine Cylinders ROUGH MACH. CYLINDER FORGING, O.D. 25.72� +0.00�/-0.12� x I.D. 19.41� + 0.12�/-0.00� x 215.63� +1.00�/-0.00� per drawing P629297 Rev B. Manufacturer responsible to procure forgings to the following specification, that can be rough machined to drawing P629297 Rev B. Material Spec. � Open Die Rough Machined Forging Cylinder. Composition: Grade 3 ASTM E723, Grade 3 Class 2a. Material Properties: Yield Strength (@ 0.2% offset 150 KSI � 130 KSI Min. 150KSI Max 1MInCVN at -40 =30ft-lbs, Min % Red. Of Area =43% Fracture Toughness 150KSI ??In From Conversion of J|c Measured using ASTM E1820. Drawing BL-55982 is rough machined forging, use as raw material that is to be made into Drawing P629297. The following test requirements for the forging are listed on the finished machine Drawing P629297. Manufacturer will make required test specimens (tension and charpy) from ends of forging per drawing note 11 and have each specimen tested per drawing note 11. Specimens must be able to meet requirements shown in note 11, A through E. Results of testing report shall be from a certified vendor. A. Tensile strength: 145 KSI Min, B. Yield strength:135 KSI, C. Charpy� Transverse: Average for 3 - 30 ft. Lbs. D.� Charpy Longitudinal: Average for 3 - 50 ft. Lbs. E.� KIC � 150 KSI � SQ �RT- IN MIN. Forging shall be ultrasonically inspected after heat treatment in accordance with ASTM A388/A388M using both the straight beam technique and angle beam technique. In two circumferential directions. Any reflectors that produce indications along with angle beam � any reflection that produce indications along with a complete loss of reflection is unacceptable. � �Manufacturer should have the machine tool turning capabilities to turn outside diameters of 25.72� +.00� -.00� x 215.63� length rough forging, to finish O.D.�s of �25.000��.031� x 214.625� length. 25.125�-.010 saddle mount diameters at the 39.50 and 53.38 length locations. Must be able to machine the end of cylinder details on the I.D., face and O.D. of both ends of cylinder to component tolerances. Manufacturer should have the machine tool capabilities to rough bore from raw material size of 19.41 I.D. to semi-finished size of 19.950 I. D. of forging the full 215.63 length of forging maintaining the required straightness, concentricity and wall variation requirements. This semi-finished size will leave material for finish honing of component to finish. Manufacturer should have the machine tool capabilities to finish hone the I.D. bore diameters to required 16 RMS? finish on I.D. bore diameters (bores to be held to 20.000� +.005). Must be able to achieve RMS finishes required on remainder of component. Manufacturer must have the machine tool capabilities to machine drilled, milled, and tap/thread holes in the face of the ends of cylinders and pressure ports on the O.D. of component at drawing locations. Manufacturing contractor will be responsible for any and all required tooling, (Mills, Drills Inserts, Taps) all applicable fixturing. This includes making of shop made fixtures, e.g. � turning plugs, cat head rings & supports, boring reamers, hone heads. Manufacturer must have machine tool capabilities to bore / thread required inside dimensions and details, e.g. Long enough boring bars, suitable tooling holders, etc. Hold positional tolerances, length and diametrical tolerances of .001� where applicable. Again, shop floor made fixtures may be needed. Manufacturer must have machine tool capabilities to mill / drill / ream / tap required features and details. Hold positional, length and diametrical tolerances of .0002� where applicable. Contractor must package each Arresting Engine component for transport to WVA in such a way to prevent any damage to component in transit. ITEM DESCRIPTION AND CAPABILITIES: Test Sections - Arresting Engine Cylinders 1. MISC-0A474 TEST SECTION is basically a short cylinder version of the long cylinder made from the same forging material - DWG-BL-55982 and cut into short (20 inch) test components representing the left end detail of the full size DWG-P629297 and all requirements, Inspection, dimensional and material properties required for the full size cylinder are applicable to MISC-0A474 TEST SECTION component. I.D. bore must be finished honed with same process machine tools as long cylinders (Honed finish bore on long cylinder restricts short test specimens to hone process for finishing). 2. Manufacturer must be able to achieve surface finishes required on surfaces, and manufacture this component to drawing specifications and dimensional tolerances. 3. Manufacturer must be able to inspect finish components to drawing requirements. Produce an inspection report with all variable data recorded. 4. Manufacturer must have the capabilities to mag particle inspect each finished machined -MISC-0A474 TEST SECTION- and P629297 ARRESTING ENGINE. These components will require 100% mag particle inspected in accordance with ASTM E709 performed by at least (2) longitudinal methods perpendicular to each other. Wet process shall be used. Internal bore shall be visually inspected in accordance with MIL-STD-2035 all / any indications found by VT shall be further investigated using dye penetrant inspection in accordance with ASTM E165/E165M) No indications over .062� are permitted. 5. Contractor must package each MISC-0A474 Test Section for transport to WVA in such a way to prevent any damage to any component in transit. 6. Drawings of components will be supplied for process development, machine tool selection and requirements in drawing note details. CAUTION: This solicitation will be issued electronically to betaSAM as will any amendments thereto. Because of this, the Government is under no obligation and is in fact unable to maintain a bidder's mailing list. It is therefore incumbent upon any interested parties to periodically access the above Internet address in order to obtain any amendments that may be issued. Failure to obtain any said amendments and to respond to them prior to the date and time set for receipt of offers may render your offer nonresponsive and result in the rejection of same. Technical Data Package: Instructions will be available in the solicitation on how to access the associated technical data package. Critical Military Technical Data: The solicitation document contains information that has been designated as ""Militarily Critical Technical Data."" Only businesses that have been certified by the Department of Defense, United States/Canada Joint Certification Office, have an active DD2345 and have a valid requirement may have a copy of the solicitation document and technical data. To obtain certification, contact the Defense Logistics Information Service (DLIS) at 800.352.3572 or http://www.dlis.dla.mil/ccal. Requests for technical data from foreign sources or representatives (other than Canada) will not be considered. In order to be eligible for award, the successful offeror's System for Award Management (SAM) Registration must be active and include representations and certifications.
- Web Link
-
SAM.gov Permalink
(https://beta.sam.gov/opp/0e7584afd64841c7af128486ac8e0262/view)
- Place of Performance
- Address: Watervliet, NY 12189, USA
- Zip Code: 12189
- Country: USA
- Zip Code: 12189
- Record
- SN05880572-F 20201225/201223230112 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |