SOLICITATION NOTICE
46 -- Lagoon Aerator Assembly
- Notice Date
- 9/9/2025 12:23:12 PM
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 333998
—
- Contracting Office
- W6QM MICC-FT DRUM FORT DRUM NY 13602-5220 USA
- ZIP Code
- 13602-5220
- Solicitation Number
- W911S225U2011
- Response Due
- 9/16/2025 1:00:00 AM
- Archive Date
- 09/09/2026
- Point of Contact
- Juanito Bautista, Phone: 8313863428
- E-Mail Address
-
juanito.d.bautista.civ@army.mil
(juanito.d.bautista.civ@army.mil)
- Small Business Set-Aside
- SBA Total Small Business Set-Aside (FAR 19.5)
- Description
- Waste Water Aerator System MOTOR:HORSEPWER: 14.5-15.5RPM: 1150-1250Full Load AMPS:42/21Voltage 230/460Voltage Phase: 3Cycle: 60Service Factor: 1.15-1.20Insulation Class: ?F? NON-Hygroscopic Bearings:Double Row Angular Contact Bearing Life: 950K-1200K hours Enclosure: Totally Enclose Fan-Cooled Motor (TEFC)MOTORSHAFT: Shaft Material: 17-4 Precipitation-Harding (PH), Stainless steel ( S.S), 1150 Condition Shaft Length: 28inches fromend shield face of motor Shaft Diameter: 1.625 inch O.D Minimum Yield Strength: 135K PSI Maximum Yield Strength: 250KPSIPROPELLER: Material: 316 Stainless Steel Balancing: Dynamically to Less than ? MIL Maximum DEFLECTOR: Material:304 Stainless Steel, HDG Steel and FRP Exterior Finish: CHEM. Resistant GEL-Coat UV Plate Internal Fill: #3 Quartzite andResin Mixture Minimum FRP Thickness: .375 inch Exterior Color: White Weight: 485-490 LBs POWER MODULE SUPPORTRING: Material: 304 Stainless Steel Dimensions of Flat Rings: .5inch by 3inch by 42 inches O.D. Dimensions of support Rod:1.5 inch by 6 inches Method of construction: Welded AERATOR FLOAT: Method of Construction: Hand Lay Up Material: CDM2415 PROMAT and Chemical Resistant Resin External Finish: Chemical Resistant Gel-Coat UV Stabilized External Color:White Internal Reinforcing (Power Module Support) 3/8 in by 3 inch by 42 inches O.D. Steel Ring Internal Reinforcing (MooringEyes): 3/8inch by 3inches by 9 inches Flat Bar Throat Section Reinforcing: 2inch by 2 inch Encapsulated Ribs Internal Fill:2#DEN. Polyurethane Closed Cell Foam Minimum Thickness: .25inch NON-Stress Areas Mooring Eye Dimension 5/8 inchby 3 inch long Float Diameter: 88 inches Float Thickness: 14 inches Sink Safety Factor: 2.5Volute Thickness: FRP .75 inchThick PERFORMANCE: Pumping Rate: 12,172 GPM02 Transfer Rate: 3.0 LBS/HP/HR/Min Minimum DIA. Of Complete Mix at6 feet Depth: 80 Feet Minimum DIA. Of O2 Dispersion at 6feet Depth: 210 Feet WT. Of Completed Unit: estimated 1700 LBSShipping WT Height of Complete Unit: minimum 54 inches/ max 60 inches. Vendor Provide Aerator Dimensions Chart andmanual Mustbe able to deliver on Weekdays 7am to 3 pm
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/e187054f19b84615a9e31ec8c6959174/view)
- Place of Performance
- Address: USAG Ft Hunter Liggett B319 Lagoon Dr Jolon, CA 93928 93928
- Zip Code: 93928
- Zip Code: 93928
- Record
- SN07584024-F 20250911/250909230053 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |