Loren Data's SAM Daily™

SAMDAILY.US - ISSUE OF MAY 28, 2026 SAM #8949
SPECIAL NOTICE

66 -- UV LIGHT CURING SYSTEM ANTON PAAR MCR 502 WESP STRESS CONTROLLED SHEAR RHEOME AND INSTALLATION

Notice Date

5/26/2026 8:51:49 AM
 

Notice Type

Special Notice
 

NAICS

334516 — Analytical Laboratory Instrument Manufacturing
 

Contracting Office

DEPT OF COMMERCE NIST GAITHERSBURG MD 20899 USA
 

ZIP Code

20899
 

Solicitation Number

NB643100-26-01720
 

Response Due

6/10/2026 5:00:00 AM
 

Archive Date

06/25/2026
 

Point of Contact

Prateema E. Carvajal, Phone: 3019754390
 

E-Mail Address

prateema.carvajal@nist.gov
(prateema.carvajal@nist.gov)
 

Description

The National Institute of Standards and Technology (NIST) intends to negotiate, on a sole source basis, under the authority of FAR 13.106-1(b) (1), with Anton Paar, 10215 Timber Ridge DR, Ashland, Virginia, for the purchase of an UV Light Curing System for an existing Anton Paar MCR 502 WESP Rheometer, needed by the Security Technologies Group at NIST. The Security Technologies Group (STG) within the Materials Measurement Science Division conducts research on complex and emerging material systems relevant to body armor and ceramic additive manufacturing (AM). These materials, including densely filled composite formulations, ceramic photopolymer slurries, and UV-curable polymer composites, exhibit properties that depend strongly on processing history, including shear, temperature, cure conditions, and microstructural evolution. A critical measurement need in these efforts is the ability to quantify UV-curing rheokinetics during photopolymerization under controlled conditions relevant to manufacturing processes and end-use performance. These measurements are required to assess viscosity increase, gel point, modulus evolution, and cure kinetics during UV exposure, while directly correlating these responses with curing parameters such as light intensity, wavelength, and exposure profile. The STG seeks to add a UV light-curing system, an optical accessory, for the existing Anton Paar MCR 502 WESP stress-controlled shear rheometer, Serial Number 83291166, located in Building 220, Room A218, on the NIST Gaithersburg campus. The system must enable simultaneous UV irradiation and rheological testing with temperature control and calibrated wavelength and intensity options. This integration creates unique requirements for the optical accessory Sole source determination is based on the need to purchase an optical accessory for the existing Anton Paar MCR 502 WESP stress-controlled shear rheometer. Purchasing a non-factory system and attempting to modify it to fit the existing rheometer runs the risk of violating the warranty and service contracts on the existing rheometer, or potentially rendering it inoperable. In addition, based on past experience with custom instrument modifications, it will likely take at least 100 person hours to identify, setup, and configure any new software packages, and to modify custom software to support the new accessory, which may be difficult or impossible to interface with the existing instrument control software. In addition, it will take about 4 person hours to train all of the users on the new software and protocol. The cost to the government for these 104 person hours is estimated to be approximately $20K. In addition, the requirement to support and operate two software packages during testing will likely require at least 32 person hours annually, at a cost of approximately $4K annually. Considering both initial costs and reoccurring costs for a 10 year life of the UV accessory results in a cost to the government of $60K. Anton Paar is the only known vendor who can provide the required accessory optical accessory UV light-curing system, for the existing Anton Paar MCR 502 WESP stress-controlled shear rheometer, Serial Number 83291166, installation, and training. The North American Industry Classification System (NAICS) code for this acquisition is 334516, Analytical Laboratory Instrument Manufacturing, with a size standard of 1,000 employees. A determination by the Government not to complete with the proposed acquisition based upon responses to this notice is solely within the discretion of the Government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement. No solicitation package will be issued. This notice of intent is not a request for competitive quotations. However, responses received by June 10, 2026, 8:00 am, ET will be considered by the Government.
 

Web Link

SAM.gov Permalink
(https://sam.gov/workspace/contract/opp/84464c6b92574e6e9fe89bae0ffe755e/view)
 

Place of Performance

Address: Gaithersburg, MD 20899, USA

Zip Code: 20899

Country: USA
 

Record

SN07828156-F 20260528/260526230044 (samdaily.us)
 

Source

SAM.gov Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's SAM Daily Index Page |